Heightening T-shaped bracket for aluminum-magnesium-manganese metal roof
Aluminum-magnesium-manganese metal roof buckle (aluminum-magnesium-manganese plate flat roof fixed support)
The fixed support for aluminum-magnesium-manganese metal roof is also called aluminum-alloy support. It is made of aluminum alloy. The common specifications are 75mm, 110mm, 165m (etc. The height of the aluminum plate rib is determined by H=H1 H2, H is the height of the aluminum alloy support, H1 is the height of the insulation material, and H2 is the height of the aluminum-magnesium-manganese plate). There are many types of T-shaped bearings. In addition to the T-shaped type, the common ones are the opposite-sex friend bearings and solar power bearings. In all flat roof system software, the aluminum alloy bearing is mainly used as the supporting point of the roof panel (effect (the aluminum-magnesium-manganese control panel will be immediately buckled on the T-shaped bearing, and then the key of the tooth occlusion machine can be used).) It is better than Generally, the installation and installation of flat houses are more scientifically researched, and the moisture-proof effect is stronger.
T-shaped support installation and installation: it is immediately stabilized on the roof purlin with screws, and it should be ensured that it is the purlin is vertical, and parallel planes are ensured between the support and the support. The selection of the installation operation distance of the aluminum alloy support is to have the total width of the aluminum-magnesium-manganese-aluminum alloy roof panel (such as yx65-430 aluminum-magnesium-manganese plate, the support spacing should be 430mm. The left and right spacing is 1000mm~1500mm, design The specification is 1200mm.) In the aluminum-magnesium-manganese-aluminum alloy roof panel, it is mainly divided into two types of aluminum-magnesium-manganese metal roofs, namely, standing double overlock seams and standing single overlock seams, namely 25 wave height and 65 wave height. Here we only introduce the 65 wave height aluminum Magnesium-manganese-aluminum alloy roof panels.
There are also many types of aluminum-magnesium-manganese board supports. In addition to T-shaped, special-shaped supports and solar supports are commonly used. The aluminum alloy support is mainly used to support the roof panel in the entire roof system, that is, the aluminum-magnesium-manganese plate is directly buckled on the T-shaped support, and then the bite machine can be used to bite it. It is more scientific than ordinary roof installation and has better waterproof effect. So how to install and use the aluminum-magnesium-manganese plate support?
First of all, the flatness of the C-shaped steel/Z-shaped steel of the purlin of the steel structure roof is adjusted to ensure that it is flat and there is no leakage.
The second step is to install the color steel plate or the bottom plate, which is divided into upside down or upside down. The upside down plate is installed under the purlin. This installation is more troublesome. You need to use scaffolding below. When installing the scaffolding, you need to pay attention to safety and carefulness. The steel tile perforated bottom plate should be positively pressed because the paint is facing downwards. If it is upright hanging, no scaffolding is needed for installation, just install the bottom plate directly on the purlin and fix it with self-tapping nails.
Aluminum sheet for roofing
The third step is to install the aluminum-magnesium-manganese board and aluminum alloy bracket. Friends who have done the installation before know that the bracket of the hidden color steel roof panel used to install the bracket while laying the board, but the aluminum-magnesium-manganese board is different. The bracket is fixed, first mark the position of the purlin with ink fountain line, and then install the T-shaped aluminum alloy support while laying the non-woven fabric. The distance of the T-shaped aluminum alloy support is based on the version of the aluminum-magnesium-manganese plate To decide, if a 65-430 aluminum-magnesium-manganese board is used, the lateral spacing of the support is better to 425mm. Note: If the fixed position of the support is just on the corrugation of the color steel perforated board, which type must be used at this time The keel is fixed, and then the supports are fixed on several types of keels.
The third step is to install the aluminum-magnesium-manganese board and aluminum alloy bracket. Friends who have done the installation before know that the bracket of the hidden color steel roof panel used to install the bracket while laying the board, but the aluminum-magnesium-manganese board is different. The bracket is fixed, first mark the position of the purlin with ink fountain line, and then install the T-shaped aluminum alloy support while laying the non-woven fabric. The distance of the T-shaped aluminum alloy support is based on the version of the aluminum-magnesium-manganese plate To decide, if a 65-430 aluminum-magnesium-manganese board is used, the lateral spacing of the support is better to 425mm. Note: If the fixed position of the support is just on the corrugation of the color steel perforated board, which type must be used at this time The keel is fixed, and then the supports are fixed on several types of keels.
Corrugated aluminum sheet
The height of the support is determined by the height of the insulation cotton and the rib height of the aluminum-magnesium-manganese alloy plate, that is, H=H1 H2, H is the height of the aluminum alloy support, H1 is the height of the insulation cotton, and H2 is the rib height of the aluminum-magnesium-manganese plate.
Post time: Sep-06-2021